Development board version introduction
Overview
Core1106 is a stamp-hole system-on-module based on the RV1106 series SoCs. It measures 30 mm × 30 mm and exposes 112 pins. The series includes eight models with either 8 GB eMMC or 256 MB SPI NAND storage:
- Core11060208 / Core11061208 / Core110602N256 / Core110612N256 use the RV1106G2 with 128 MB DDR3L and a 0.5 TOPS NPU.
- Core11060408 / Core11061408 / Core110604N256 / Core110614N256 use the RV1106G3 with 256 MB DDR3L and a 1 TOPS NPU.
- Core11061208 / Core11061408 / Core110612N256 / Core110614N256 provide 2.4 GHz Wi-Fi 6, Bluetooth 5.2, and BLE connectivity.
Each model exposes MIPI CSI, RGB666, USB 2.0 Host/Device, 100 Mbps Ethernet, audio, and GPIO interfaces through the stamp-hole connectors. The NPU supports INT4, INT8, and INT16 mixed-precision operations, and the hardware video encoder supports H.264/H.265. ISP input specifications depend on the SoC: RV1106G2 supports up to 5 MP at 30 fps, and RV1106G3 supports up to 8 MP at 15 fps. Core1106 is supported by the Buildroot system and SDK for carrier-board design and embedded vision product integration.
Basic Specifications
| Core11060208 | Core11061208 | Core11060408 | Core11061408 | Core110602N256 | Core110612N256 | Core110604N256 | Core110614N256 | |
|---|---|---|---|---|---|---|---|---|
| SOC | RV1106G2 | RV1106G3 | RV1106G2 | RV1106G3 | ||||
| Processor | Cortex A7 1.2GHz | |||||||
| NPU | 0.5 TOPS, supports INT4, INT8, and INT16 | 1 TOPS, supports INT4, INT8, and INT16 | 0.5 TOPS, supports INT4, INT8, and INT16 | 1 TOPS, supports INT4, INT8, and INT16 | ||||
| VEPU | Supports H264/H265 video encoder | |||||||
| ISP | Up to 5 MP @ 30 fps | Up to 8 MP @ 15 fps | Up to 5 MP @ 30 fps | Up to 8 MP @ 15 fps | ||||
| Memory | 128MB DDR3L | 256MB DDR3L | 128MB DDR3L | 256MB DDR3L | ||||
| Wi-Fi+Bluetooth | / | 2.4GHz WiFi6 Bluetooth 5.2/BLE | / | 2.4GHz WiFi6 Bluetooth 5.2/BLE | / | 2.4GHz WiFi6 Bluetooth 5.2/BLE | / | 2.4GHz WiFi6 Bluetooth 5.2/BLE |
| Default Storage Medium | eMMC(8GB) | SPI NAND(256MB) | ||||||
| Core board size | 30 mm × 30 mm | |||||||
| Stamp pin | 112 Pin | |||||||
| Operating Temperature Range | -20~60 ℃ | |||||||
Functional Parameters
| Function | Quantity | Parameters | |||||||
|---|---|---|---|---|---|---|---|---|---|
| MIPI CSI | ≤2 | Supports 2 CSI-2 interfaces, each with 2 D-PHY v1.2 data lanes. These 2 interfaces can be combined into a single interface with 4 data lanes. | |||||||
| Display | 1 | 18-bit(RGB666) | |||||||
| USB | 1 | USB 2.0 Host/Device | |||||||
| Ethernet | 1 | 10/100M Ethernet controller and embedded PHY | |||||||
| Audio | 1 | LINEOUT | |||||||
| 2 | Analog differential MIC interface. | ||||||||
| I2S | ≤3 | Supports 8 TX lanes and 8 RX lanes. Supports 3 I2S modes (Standard I2S, Left-Justified, Right-Justified). Supports 4 PCM formats (Early mode, Late1 mode, Late2 mode, Late3 mode). Supports a maximum sampling rate of 192kHz. Supports audio resolution: 16 to 32 bits. | |||||||
| I2C | ≤5 | Supports 7-bit and 10-bit address modes. Standard mode data transfer rate: 100k bits/s, in fast mode: 400k bits/s. | |||||||
| SPI | ≤2 | Supports master and slave modes, with each interface supporting two chip selects. | |||||||
| SDIO | ≤2 | Compatible with SDIO 3.0 protocol, 4-bit mode. | |||||||
| ADC | ≤2 | Supports 2-channel 10-bit single-ended input SAR-ADC with a sampling rate of up to 1MS/s. | |||||||
| UART | ≤6 | Built-in 2-channel 64-bit FIFO, separately used for TX and RX. Supports 5-bit, 6-bit, 7-bit, and 8-bit serial data transmission and reception, with a baud rate of up to 4Mbps. | |||||||
| PWM | ≤12 | Embedded 32-bit timer/counter functionality. Supports capture mode. | |||||||